How To Change IP Address In Less Than 1 Minute

Just follow this simply instructions :

1. Click on "Start" in the bottom left hand corner of screen
2. Click on "Run"
3. Type in "command" and hit ok

You should now be at an MSDOS prompt screen.

4. Type "ipconfig /release" just like that, and hit "enter"
5. Type "exit" and leave the prompt
6. Right-click on "Network Places" or "My Network Places" on your desktop.
7. Click on "properties"

You should now be on a screen with something titled "Local Area Connection", or something close to that, and, if you have a network hooked up, all of your other networks.

8. Right click on "Local Area Connection" and click "properties"
9. Double-click on the "Internet Protocol (TCP/IP)" from the list under the "General" tab
10. Click on "Use the following IP address" under the "General" tab
11. Create an IP address (It doesn't matter what it is. I just type 1 and 2 until i fill the area up).
12. Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers.
13. Hit the "Ok" button here
14. Hit the "Ok" button again

You should now be back to the "Local Area Connection" screen.

15. Right-click back on "Local Area Connection" and go to properties again.
16. Go back to the "TCP/IP" settings
17. This time, select "Obtain an IP address automatically"
tongue.gif 18. Hit "Ok"
19. Hit "Ok" again
20. You now have a new IP address

With a little practice, you can easily get this process down to 15 seconds.

P.S:
This only changes your dynamic IP address, not your ISP/IP address. If you plan on hacking a website with this trick be extremely careful, because if they try a little, they can trace it back


How To Get Any Windows Password

this works whether its windows 2000 or windows xp or windows xp SP1 or SP2 or windows server 2003....

this works even if syskey encryption is employed...

if it is FAT filesystem...

just copy the sam file like stated in the first post to an empty floppy disk and take it home. I'll tell u what to do with it later... DON'T DELETE THE ORIGINAL SAM FILE. just remove its attributes. the sam file is a file called SAM with no extension. YOU MUST ALSO GET.... a file called SYSTEM which is in the same folder as SAM. both files have no extensions...

if it is NTFS....

u have to download a program called NTFSPro.... it allows u to read from ntfs drives... the demo version allows read only. the full version is read-write.... you use the program to create an unbootable disk (so u will still need another bootable disk and an empty disk) that has the required files to access NTFS.

use the boot disk to get into dos, then use the disks created with ntfspro to be able to access the filesystem, then copy the SAM and SYSTEM files to another empty disk to take home....

AT HOME: u have to get a program called SAMInside. it doesn't matter if it is demo version. SAMInside will open the SAM file and extract all the user account information and their passwords, including administrator. SAMInside will ask for the SYSTEM file too if the computer you took the SAM file from has syskey enabled. syskey encrypts the SAM file. SAMInside uses SYSTEM file to decrypt the SAM file. After SAMInside finishes, u still see user accounts and hashes beside them. the hashes are the encoded passwords. Use SAMInside to export the accounts and their hashes as a pwdump file into another program, called LophtCrack. it is currently in version 5, it is named LC5. the previous version, LC4 is just as good. u need the full or cracked version of the program. LC5 uses a brute force method by trying all possible combinations of letters numbers, and unprintable characters to find the correct password from the hashes in the pwdump file imported into it from SAMInside. This process of trying all passwords might take 5 minutes if the password is easy, up to a year if the password is long and hard (really really hard). LC5 howver, unlike LC4, is almost 100 times faster. both can be configured to try dictionary and common words before using all possible combinations of everything. Once the correct password is found, it will display the passwords in clear beside each account, including administrator.

I use this method so many times. I've compromised the whole school computer infrastructure. LC4 usually took between 1 second and 10 minutes to find the passwords because they were common words found in any english dictionary. I haven't used LC5 yet.

If there is anything unclear, anything I overlooked, plz tell me so that I can turn this into a very easy to follow tutorial to help anybody crack any windowz pass.

Programs needed: SAMInside (doesn't matter which version or if demo)
LC4 or LC5 (lophtcrack)( must be full version)
NTFSPro (doesn't matter if demo)
any bootdisk maker

Cracked or full version software can be found on any warez site.


How To Modify EXE Files

learn how to change *.exe files, in 5 easy steps:

1) Don't try to modify a prog by editing his source in a dissasembler.Why?
Cause that's for programmers and assembly experts only.

try to view it in hex you'll only get tons of crap you don't understand.
First off, you need Resource Hacker(last version). It's a resource editor-
very easy to use, You can download it at http://www.users.on.net/johnson/resourcehacker/

2) Unzip the archive, and run ResHacker.exe. You can check out the help file too

3) You will see that the interface is simple and clean. Go to the menu FileOpen or press Ctrl+O to open a file. Browse your way to the file you would like to edit. You can edit *.exe, *.dll, *.ocx, *.scr and *.cpl files, but this tutorial is to teach you how to edit *.exe files, so open one.

4) In the left side of the screen a list of sections will appear.
The most common sections are
-String table;
-RCData;
-Dialog;
-Cursor group;
-Bitmap;
-WAV.
*Icon: You can wiew and change the icon(s) of the program by double-clicking the icon section,chossing the icon, right-clicking on it an pressing "replace resource". After that you can choose the icon you want to replace the original with.
*String table: a bunch of crap, useful sometimes, basic programming knowladge needed.
*RCData: Here the real hacking begins. Modify window titles, buttons, text, and lots more!
*Dialog:Here you can modify the messages or dialogs that appear in a program. Don't forget to press "Compile" when you're done!
*Cursor group: Change the mouse cursors used in the program just like you would change the icon.
*Bitmap: View or change images in the programs easy!
*WAV:Change the sounds in the prog. with your own.

5) In the RCData,Dialog,Menu and String table sections you can do a lot of changes. You can modify or translate the text change links, change buttons, etc.

TIP: To change a window title, search for something like: CAPTION "edit this".
TIP: After all operations press the "Compile Script" button, and when you're done editing save, your work @ FileSave(Save as).
TIP: When you save a file,the original file will be backed up by default and renamed to Name_original and the saved file will have the normal name of the changed prog.
TIP: Sometimes you may get a message like: "This program has a non-standard resource layout... it has probably been compressed with an .EXE compressor." That means that Resource Hacker can't modify it because of it's structure.


Easy How To Download From ShareCash.Org

What Is ShareCash? - ShrareCash.Org Simply Review

ShareCash is a next-generation upload site, where you get paid CASH for every download you get! Simply register, upload files, and let the cash start rolling in!

Unlike other upload websites that give you pathetically low prices, such as $10 for 1000 US downloads, well give you 30-60 cents PER DOWNLOAD! Thats $600 for 1000 US downloads - sixty times more than any other upload cash website! --- Start Earning With ShareCash Now!

How To Download Files From ShareCash.Org ?

Note : This Method Only Work On FireFox!

1. Open your firefox browser
2. Go to addons.mozilla.org and install GreaseMonkey to your firefox
3. After GraseMonkey addons was already installed on your firefox, go to UserScript.Org and seacrh for ShareCash AutoDownload script then install it to your GreaseMonkey.
4. FINISH!! ... now you can download any files from ShareCash.Org without have to fill out the CPA form and no matter where you came from.



If you are still unable to download from ShareCash, visit : Sharecash Review


How To Unload Cached DLL Files To Free Memory

Windows Explorer caches DLLs (Dynamic-Link Libraries) in memory for a period of time after the application an using them has been closed. Which in some cases can be an waste of memory. To stop WinXP from always caching these DLL files, create the new registry key below.

Open up the Registry and navigate to :

HKEY_LOCAL_MACHINE\ SOFTWARE\ Microsoft\ Windows\ CurrentVersion\ Explorer

Create a new sub-key named 'AlwaysUnloadDLL' and set the default value to equal '1' to disable Windows caching the DLL in memory.

Restart Windows for the change to take effect


How To Stop Spam

Change Mcft to microsoft

HOW TO STOP SPAM VIA WINDOWS MESSENGER SERVICE
Below you'll find many ways (sorted in the most successful ratio first) to stop the Windows Messenger service, depending on your system environment, some may require more than one process. This service is available only on NT, 2K, XP & Server 2003. Administrator Login is REQUIRED

About The Messenger Service

* Messenger is a Windows Service that runs in the background
* Messenger is not the same as MSN Messenger or any other Instant Messaging Program
* Messenger does not facilitate two-way chatting
* Many Windows Programs, Firewalls, UPS and Antiviruses require the Messenger Service
* Antivirus and UPS software, among others, may not work if Messenger is disabled
* The Messenger Service is usually turned on by default in most Windows NT, 2K and XP systems

1. Manually

1. Example 1

1. Click Start, Run and enter the following command:
RunDll32 advpack.dll, LaunchINFSection %windir%\inf\msmsgs.inf, BLC.Remove
NOTE: This will prevent a long delay when opening Outlook Express if you have the Contacts pane enabled
2. To prevent this, click Start, Run and enter {REGEDIT} Go to:
HKEY_LOCAL_MACHINE\Software\Mcft\Outlook Express
3. Right click in the right pane and select New, Dword value
4. Give it the name Hide Messenger Double click this new entry and set the value to 2
5. End result should look EXACTLY like this:
System Key: [HKEY_LOCAL_MACHINE\SOFTWARE\Mcft\Outlook Express]
Value Name: Hide Messenger
Data Type: REG_DWORD (DWORD Value)
Value Data: (2 = remove messenger)

2. Example 2

1. Copy and paste the following to Run Command Bar in the Start Menu:
RunDll32.exe advpack.dll,LaunchINFSection
%windir%\inf\msmsgs.inf,BLC.Remove

3. Example 3

1. If Example 5 didn't work, then try this - Many users miss or don't know of it
2. Click on Start then go to RUN and type:
C:\WINDOWS\inf\sysoc.inf
3. Change:
msmsgs=msgrocm.dll,OcEntry,msmsgs.inf,hide,7
4. To:
msmsgs=msgrocm.dll,OcEntry,msmsgs.inf,7
5. Then use Add/Remove Windows Components to remove Messenger
NOTE: You can also prevent access to Windows Messenger using Group Policy or the Set Program Access and Defaults utility added by default in Windows XP SP1 and Windows 2000 SP3

4. Example 4

1. Open Windows Messenger
2. From the menu, select "Tools" then "Options" then "Preferences" tab
3. Uncheck "Run this program when Windows starts"
4. Open Outlook Express
5. From the menu, select "Tools" then "Options" then "General" tab
6. Uncheck the option to "Automatically log on", if it's there
7. Also in Outlook Express, select "View" then "Layout"
8. Uncheck the option to "display Contacts" - The program will open a connection and display a list of all Contacts on line if you do not
9. In "Startup Folder" make sure there is no entry there for Messenger
10. Open Norton Anti-Virus if you have it installed
11. Click "Options" then "Instant Messenger"
12. Unckeck "Windows Messenger (recommended"
NOTE: This list ought to work in disassociate MSN from Outlook Express, so that it'll only start up if you really want it to

5. Example 5

1. 2000

* Click Start-> Settings-> Control Panel-> Administrative Tools->Services
* Scroll down and highlight "Messenger"
* Right-click the highlighted line and choose Properties
* Click the STOP button
* Select Disable in the Startup Type scroll bar
* Click OK

2. XP Home

* Click Start->Settings ->Control Panel
* Click Performance and Maintenance
* Click Administrative Tools
* Double click Services
* Scroll down and highlight "Messenger"
* Right-click the highlighted line and choose Properties
* Click the STOP button
* Select Disable in the Startup Type scroll bar
* Click OK

3. XP Professional

* Click Start->Settings ->Control Panel
* Click Administrative Tools
* Click Services
* Double click Services
* Scroll down and highlight "Messenger"
* Right-click the highlighted line and choose Properties.
* Click the STOP button.
* Select Disable in the Startup Type scroll bar
* Click OK

4. Windows NT

* Click Start ->Control Panel
* Double Click Administrative Tools
* Select Services-> Double-click on Messenger
* In the Messenger Properties window, select Stop
* Then choose Disable as the Startup Type
* Click OK
NOTE: If you stop the service and don’t adjust the startup type, the Messenger service will start automatically the next time you reboot. Keep in mind that when you disable the Messenger service, you'll no longer receive messages about an attached UPS, and you won’t be notified of print job completion, performance alerts, or antivirus activity (from Windows) not the program you're using for those purposes.

6. Example 6

1. To disable receipt of messenger pop-ups, verify that your firewall disables inbound traffic on UDP ports 135, 137, and 138, and TCP ports 135 and 139. On a system connected directly to the Internet, you should also disable inbound traffic on TCP port 445. If the system you want to protect is part of a Win2K-based network with Active Directory (AD), don't block incoming traffic on port 445 - Mcft Knowledge Base Article - 330904
Code:
http://support.Mcft.com/default.aspx?scid=kb;en-us;330904

NOTE: You can use the firewall approach only if your system doesn't communicate with legacy systems that rely on NetBIOS name resolution to locate machines and shared resources. If, for example, you let users running Windows 9x share your printer or scanner, when you disable inbound NetBIOS traffic, users won't be able to connect to these shared resources. Regardless of the method you choose, you can stop messenger spam

2. Program

1. Example 1

NOTE: On Oct 15, 2003, Mcft releases Critical Security Bulletin MS03-043 warning users that the Windows Messenger Service running and exposed by default in all versions of Windows NT, 2000 and XP, contains a "Remote Code Execution" vulnerability that allows any not otherwise secured and protected Windows machine to be taken over and remotely compromised over the Internet
1. Shoot the Messenger
Code:
http://grc.com/files/shootthemessenger.exe

2. Example 2

1. Messenger Disable
Code:
http://www.dougknox.com/xp/utils/MessengerDisable.zip

NOTE: If you choose to uninstall Windows Messenger on a system with SP1 installed, you will receive an error message about "un-registering" an OCX file. This is normal, and doest not affect the removal process. Windows Messenger will still be removed

3. TEST

1. Example 1

1. Right-click "My Computer"
2. Select "Manage"
3. Under "System Tools" right-click on "Shared Folders"
4. Choose "All Tasks" and select "Send Console Message..."
5. If you recieve the following error message then the service has been disabled, otherwise confirm that you have disabled it or try another example
"The following error occured while reading the list of sessions from Windows clients:
Error 2114: The Server service is not started."

2. Example 2

1. Click Start then "Run"
2. Type in {cmd.exe}
3. Type in net send 127.0.0.1 hi
4. If you get a popup "hi" message, then confirm that you have disabled it or try another example

4. IF YOU INSIST

1. If you insist on keeping Windows Messenger, then I'd recommend Messenger Manager - "Allows you to keep your messenger service running, as is intended and needed by Windows. This ensures that vital system errors and notifications may be sent informing you of Important System Events"
Code:
http://www.sellertools.com/default.asp?i=MessageManager3.htm

2. However, as a replacement to Windows Messenger remote control feature, I'd recommend this free tool Virtual Network Computing - "It is a remote control software which allows you to view and interact with one computer (the "server") using a simple program (the "viewer") on another computer anywhere on the Internet. The two computers don't even have to be the same type, so for example you can use VNC to view an office Linux machine on your Windows PC at home"
Code:
http://www.realvnc.com/download.html

RESULTS WILL VARY
No matter how good your systems may be, they're only as effective as what you put into them.


How To Find Remote IP

Method 1
To view someone's IP# when they send you hotmail email do this:
1) Click "Options" on the upper right side of the page.
2) On the left side of the page, Click "Mail"
3) Click "Mail Display Settings"
4) Under "Message Headers" select "Full" or "Advanced"
5) Click ok

Method 2
reg a dydns account and install the ip pointer, so each time you ping the host name you regestored

for example:
you regestor the host name myhost.dydns.com, then you keep a little software running on the target host. The little software will keep update your IP to dydns.com server.

so at your pc just start cmd, and ping myhost.dydns.com, it will give you the most updated ip address.

Method 3
neverender, what doesn't work for you? Simply type in nc -vvv -l -p 80 on your box, which will set it to listen in verbose mode on port 80. Then give them a link to your IP address (for example: 111.111.111.11) and tell them to type it in their browser. The browser should resolve the address as well as append port 80 automatically. Just make sure that your friend is not very computer literate.

Method 4
Just download a very simple server such as this one and install it on your comp. Then run it and give your ip to the person you want and tell them to connect to it through a browser. Your server will log their connection and you will get their IP.

link:http://www.download.com/Abyss-Web-Server/3000-2165-10283992.html?tag=lst-0-6

Other Ways
-www.imchaos.com and make a "spy poll" to put in ur profile, this will tell u the IP of anybody who answers ur poll
-originalicons.com there is a page for doin it (i dont like it, but it works)
-or irc


Here is a more detailed tutorial about using NetCat.
http://www.onlamp.com/pub/a/onlamp/2003/05/29/netcat.html

Windows users can download NetCat from here :
http://www.atstake.com/research/tools/network_utilities/


How To Bypass Web Filters

There are several occasions where you will be at a public terminal, and require access to a particular website that is blocked for some reason or another. How to bypass these restrictions is a very common question, and will be covered here. Lets pretend for a moment that the Internet is made up of 26 websites, A-Z. The web filter blocks your browser from accessing sites X-Z, but not sites A-W. Simply make the browser think you’re going to A-W. There are a variety of ways to do this:

Proxy Servers :
This is a list of http proxies. These sites may not be up forever, so you may need to search for “free http proxy” or “public proxy servers” or other similar terms.

Proxy server lists :
http://www.aliveproxy.com
http://www.multiproxy.org
http://www.publicproxyservers.com/index.html
http://www.tehbox.com/proxy
http://www.proxz.com
http://www.proxy4free.com/index.html
http://free-proxies.com

Now that you have a list of proxies, you would open IE (internet explorer) and click on Tools > Internet Options > Connections > LAN Settings > Advanced. Enter the address and port of one of the servers from the list in the proper area (http) and make sure the “use a proxy server for your LAN” option is selected. Remember to replace the proxy and port at your terminal to the original when you're done.

*Note: Some proxies listed may not work, and this method may decrease your surfing speed. By trying various entries, you’ll find one that works, or works faster.

The infamous translation trick :
Go to a web page translation site and use their services to “translate a page to English” thus accessing the blocked page through their trusted site.

You’ll notice that several translation sites are blocked, but by using less popular ones, this method can still be effective. Here is a list of some translation services. Again, these sites may not be up forever, so you may need to search for them.

http://babelfish.altavista.com
http://world.altavista.com
http://translation.langenberg.com
http://freetranslation.com/web.thm

Url Scripting :
Url scripting is the easiest method. It works on a select few web filters and is based on the same principal as the translation trick. By typing and address like “www.yahoo.com@www.restricted_site.com the filter will not go into effect as it recognizes the trusted site (in this case yahoo.com)

Other tricks :
Simply open the command prompt and type:
Ping restricted.com ? restricted.com obviously being the restricted site
At this point you can take down the IP address (ex. 216.109.124.73) and enter it into the browser. If access to the command prompt is also restricted, see “How to bypass restrictions to get to the command prompt.” If this article has been taken from information leak, then know that it involves anything from opening the browser, selecting view > source, then saving it as X.bat and opening it to opening a folder or browser and typing in the location of cmd.exe depending on the OS. I will not go into further, as this a completely different topic.

Use https://restrictedsite.com as referring to it as a secured site may confuse the filter.

Note: These are ancient methods that many new filters defend against, but still may be applicable in your situation. If not, a little history never hurt anyone.

Web based Proxies :
Another one of the easier, yet effective methods include web based proxies. These are simple in the fact that you just enter the restricted address and surf! Some of these have some restrictions, like daily usage limits, etc but you can also use another proxy (perhaps one that sucks, like a text only) to bypass their restrictions as well. Here is a list of some:

• http://proxify.com]http://proxify.com
• http://www.anonymizer.com/index.cgi]http://www.anonymizer.com/index.cgi
• http://www.guardster.com/]http://www.guardster.com/
• http://anonymouse.ws/anonwww.html]http://anonymouse.ws/anonwww.html
• http://www.the-cloak.com/login.html]http://www.the-cloak.com/login.html
• https://www.megaproxy.com/freesurf]https://www.megaproxy.com/freesurf
• http://www.anonymizer.ru]http://www.anonymizer.ru
• https://nadaily.com/cgi-bin/nph-proxyb.cgi]https://nadaily.com/cgi-bin/nph-proxyb.cgi
• http://www.userbeam.de/cgi-bin/nph-userbeam.cgi]http://www.userbeam.de/cgi-bin/nph-userbeam.cgi
• http://www.free2.surffreedom.com/nph-free.cgi]http://www.free2.surffreedom.com/nph-free.cgi

Proxy Programs:
There are many proxy programs that allow you to surf anonymously that are more or less based on the same topics we’ve covered here. I’ve added them just to cover the topic thoroughly:

• http://www.hotscripts.com/Detailed/28480.html]http://www.hotscripts.com/Detailed/28480.html
• http://www.inetprivacy.com/a4proxy/anonymous-grc.htm]http://www.inetprivacy.com/a4proxy/anonymous-grc.htm
• http://www.orangatango.com/home/index.ie.html]http://www.orangatango.com/home/index.ie.html
• http://www.steganos.com]http://www.steganos.com
• http://www.anonymization.net]http://www.anonymization.net ? toolbar that requires admin rights to install

Making your own CGI proxy server:
Making your own proxy server may come in handy, but I personally find that simply uploading a txt file/w a list of proxies to a free host makes for a much easier and headache free solution. If you don’t know PERL, there is code out there to help you set it up. Check out these sites for more info:

• http://httpbridge.sourceforge.net]http://httpbridge.sourceforge.net
• http://www.jmarshall.com/tools/cgiproxy]http://www.jmarshall.com/tools/cgiproxy
• http://www.manageability.org/blog/stuff/open-source-personal-proxy-servers-written-in-java/view]http://www.manageability.org/blog/stuff/op...en-in-java/view

Admin Access:
When all else fails, you can simply take over the PC and alter or delete the damn filter. This method varies according to the OS (operating system) you are dealing with. Please see “Hacking Windows NT” for more information. If this tutorial has been taken from information leak, then I will go as far as to say it involves booting the PC in another OS, copying the SAM file and cracking it using a program like saminside or LC5 rather than start a whole new topic within one.


How To Test An AntiVirus Performance - Simply AntiVirus Review

After installing VirusScan, you may logically wonder, how do I know if it's working? The answer is a test virus. The EICAR Standard AntiVirus Test File is a combined effort by anti-virus vendors throughout the world to implement one standard by which customers can verify their anti-virus installations.

Solution :

To test your installation, copy the following line into its own file, then save the file with the name EICAR.COM. More detailed instructions are found below.

X5O!P%@AP[4\PZX54(P^)7CC)7}$EICAR-STANDARD-ANTIVIRUS-TEST-FILE!$H+H*

The file size will be 68 or 70 bytes.

If VirusScan is running and configured correctly, when you try to save the file, VirusScan will detect the virus. If VirusScan is not running, start it and scan the directory that contains EICAR.COM. When your software scans this file, it will report finding the EICAR test file.

Note that this file is NOT A VIRUS. Delete the file when you have finished testing your installation to avoid alarming unsuspecting
users.

The eicar test virus is available for download from the following website:
http://www.eicar.org/download/eicar.com

Creating Eicar.com :

1. Click on Start.
2. Select Run.
3. In the Open box type: notepad
4. Maximize the window.
5. Highlight the following on the following line of text:
X5O!P%@AP[4\PZX54(P^)7CC)7}$EICAR-STANDARD-ANTIVIRUS-TEST-FILE!$H+H*
6. Right click on the highlighted text and choose 'copy'.
7. Switch back to Notepad.
8. Right click anywhere inside of Notepad and select 'paste'.
9. Click the File menu and select 'save as'.
10. Change the 'Save as Type' to 'all files'.
11. Name the file eicar.com.


How To Fix Windows Installer Problem

Do you experience this kind of problem whenever you attemp to install an application in windows box (2k, xp)?

"The Windows Installer service could not be accessed. This can occur if you are running Windows in safe mode, or if the Windows Installer is not correctly installed. Contact your support personnel for assistance."

The ms website knowledge article 324516 gives 2 methods as a way of fixing this problem, but you might be very lucky if any of the 2 fixes the problem, alot of guys end up formating their systems and doing fresh windows installations or try wired ways of fixing it.

Well, the solution is very easy:

1. right click your root windows installation drive i.e drive where you installed windows
2. click properties at the bottom
3. select security tab
4. click Add and scroll down to SYSTEM account click add and click OK.
5. allow Full control permission and click Apply and then Ok.

This should solve your problem with windows installer.


How To Change A Cmos Battery

First the safety rules

The inside of a computer is a bad place full of electricity and sharp edges. On the electricity side always when working on you computer make sure that it’s still plugged in to the power socket and the power is turned off, this is to ensure that any static. From you is discharged through the earth. The inside of most computer cases are unfinished metal and has very sharp edges so be careful.

The first signs of a battery failing are :
1) your clock starts running slowly
2) when you boot (start) your computer it has a problem finding your hardware (no hard drive, no cd rom)

To change the battery you need the following tools
1) a X-point screwdriver
2) an anti-static strap(optional)
3) a new battery (seems logical)

Then unplug all the cables from the back of the computer as you remove them make a note where they came from. (So when you finished you can put them back)

Move the computer somewhere where you can work on it with ease

Remove the cover by locating the screws around the outer edge (back) of the computer
Some computer cases only require you to remove 2 screws on one side then a panel can be removed allowing you access to the computers insides, others you must remove 6 screws and remove the whole case by sliding it to the rear and lifting it off.

Now make sure that you read the safety instructions about static.
Look inside you will see a round silver thing that looks about the size of a 10p piece (quarter). This is the battery itself, carefully lift the retaining clip and slide the battery out. That’s it removed now go to your local computer retailer, electrical retailer (Tandy/Radio shack) taking the old battery with you and get a new battery.

Back to your computer insert the new battery by lifting the clip and sliding the battery in. Reinstall your case and plug all the cables back (you did remember to label them didn’t you)

Now for the fun part.
You will now need to go into you bios….
Right the bios is the god of your computer.
To access it, when your computer first starts you will see a black screen with white text.

If you look carefully you will see a line that says something like "press del for setup" or some other key (F2 or ESC or tab) this will take you to god's house where you can make lots of changes to the way your machine works. It is also the place where you can make your nice computer in to a rather expensive door stop so be careful and don’t go playing with anything.

You will now be presented with a blue screen with a lot of options on it, The one we want is load optimised/default settings. Press the F10 key and type y the computer should now reboot. If every thing went well then your computer will now be up and running.


How To Save Windows XP Updates

Go to the Windows Update web site.
In the left pane, under Other Options, select "Personalize Windows Update".
Under “Set Options for Windows Update", select the checkbox for “Display the Link to Windows Update Catalog under "See Also", then click "Save Settings".
Go back to the Windows Update web site.
In the left pane, under "See Also", select "Windows Update Catalog".
Select "Find Updates for Microsoft Operating Systems".
Select the operating system and language of your choice.
Select "Critical Updates and Service Packs".
Select all of the patches you’d like to download, then click on "Go to download basket" to download them.


How To Add A Url Address Bar To The Taskbar

You can add an Internet URL address bar to your Windows XP taskbar. Doing so will let you type in URLs and launch Web pages without first launching a browser. It will also let you launch some native Windows XP applications in much the same way as you would via the Run menu (so you could type in calc to launch the calculator or mspaint to launch Microsoft Paint. Here's how you add the address bar:

1. Right-click on the taskbar, select Toolbars, and then click Address.

2. The word Address will appear on your taskbar.

3. Double click it to access it.

4. If that doesn't work, your taskbar is locked. You can unlock it by right-clicking on the taskbar again and uncheck Lock the Taskbar.

NOTE: You may also need to grab the vertical dotted lines beside the word Address and drag it to the left to make the Address window appear.


  ©2009 Simply Computer Tips & Tricks. Template by Dicas Blogger.

Jump To TOP